No need to be a DIY expert to change fuses on a Jeep Renegade. This still should require some specific concepts and information, which is why we propose to help you through this article.

First, it is important to understand what role the fuse box plays on a Jeep Renegade.

Role of a fuse box on your Jeep Renegade:

This fuses box is generally used to protect electrical circuits that are essential parts of your Jeep Renegade.
It consists of a lead wire that is linked to the input circuit of the electrical circuit. Due to its technical properties, lead heats up relatively quickly when the current flows. This allows it to melt if a possible overload occurs.

Therefore, the power is cut off and the peripheral parts are maintained, but above all it prevents an overheating or even an explosion of selected sensitive parts, batteries for example. It is important to understand that this is an essential part of your Jeep Renegade

With advances in mechanics and technology, it has been assigned additional ancillary tasks over time, such as helping other electrical components, or even becoming a centralizing control box.

This suggests that even if its primary function remains unchanged, these additional tasks make its replacement a little more tough.

We will detail in the next section how to locate the fuse box in your Jeep Renegade.how-to-find-the-fuse-box-jeep-renegade

Where can i find the fuse box on my Jeep Renegade:

Now that you know its use, you almost certainly wonder where is the fuse box located in your Jeep Renegade ?
In these modern times, the vast majority of cars have 2 cases and it’s not always easy to find them.
The ideal solution remains for you to check the logbook of your Jeep Renegade.

If you don’t have this notebook, here are some suggestions to help you find your way around.

First, one of the boxes is often close to the driver’s side. It is sometimes hard to access and you may need to remove some protections from the inside of your Jeep Renegade in order to reach it.

Another possible location is in the engine compartment. Look for the battery, it’s often right next to it.

Once the box is found, you will need to find the fuse in question in order to be able to change the defective one. Indeed, on your case, each fuse corresponds to a specific role, you will have to find the matches. For example, your beam headlamps have their own fuse.
These assignments must appear in your maintenance manual of your Jeep Renegade.

Be particularly careful when removing it, you could harm the parts around it. Very often, a plastic clamp is given with it, which will greatly facilitate your work.

Different fuse models on your Jeep Renegade:

Another essential point to know when you are about to change these parts is that there are different types of fuses. We will focus here only on the most frequent models in order of size, from the smallest to the largest:

Mini fuses: They have a rating of 2 to 30 amperes. A major advantage is that they are very small and therefore not very cumbersome. Disadvantage, they have a limited resistance capacity, it does not correspond to the protection of any circuit of your Jeep Renegade.
Standard fuses: They have a slightly higher rating than mini fuses (from 3.5 to 30 amperes) but are relatively larger. They measure 2*2 CM.

Maximum fuses: These are the largest as their name suggests, they measure 3.5*2.5 CM, for an amperage of 30 to 90. Their role is mainly found on drive parts (cooling…)

Now that you have more information about these famous fuses, all you have to do now is act carefully.

Conclusion and other informations on fuse boxes

Here are also some essential rules to follow to ensure the proper functioning of your Jeep Renegade.

It is essential to substitute a fuse with a fuse corresponding to the correct amperage. Do not rely automatically on the fuse in place, it may be there by mistake.
EX: There was a short circuit on a line because the fuse in question was too small. If you replace this fuse with its equivalent, the problem is very likely to happen again.

Please refer to your Jeep Renegade’s maintenance manual for the appropriate size. Each caliber often has its own colour, which will make it easier for you to identify it.
You may possibly also wonder how to check if a fuse is blown and also if you can check it without removing it. The answer is yes.
You could easily visually inspect the element in a glass fuse to see if it has blown, but unfortunately they now mostly have solid, non-transparent bodies that hide the element from view. To know if the fuse is blown, you will have to use a multimeter. Once configured, a multimeter can measure the resistance of the fuse element. Resistance is measured in Ohms ‘Ω’.
You will find a tutorial for your Jeep Renegade of this online by simply googling it.

Last but not least, be very careful with the surrounding electronic components, you could damage important parts when handling them or even more important harm yourself !

If you want more tutorials on the Jeep Renegade, go to our Jeep Renegade category.